Auto Light lets you customize the different levels of brightness according the the environment. You just need to choose the brightness level (from 1 to 10) and set the limits of the sensor to the change the level. It is supposed to be better auto adjuster of the backlight for your phone.
Install
Run AutoLight.cab and install in main memory (not in storage card), run AutoLight.Config.cab and install where you like, then softreset (this should also disable the native auto adjust backlight function, check for that in the Control Panel Power applet).
If you have previously installed autolight V2.x and want only upgrade to V2.3 without having your configuration reset to default use the Configurator to stop AutoLight. After that overwrite AutoLight.exe, ChangeLight.exe and AutoLightConfig.exe with the files you find inside AutoLight.zip and softreset.
Configurator
AutoLight working depends on parameters it gets from registry. For details on parameters see AutoLight.reg.txt and AutoLigth.reg
The Configurator gives a more user friendly access to these parameters.
Nevertheless, the configuration process is quite complex and should be done after thoroughly reading AutoLight.reg.txt.
The second tab of the Configurator contains a graphical representation of the calibration table used to convert light sensor to backlight values. Note that: - the horizontal scale is not linear but goes according to square root of the light sensor value;
- the horizontal red segments represent the ranges of light sensor values assigned to every backlight level;
- the horizontal red segment whose backlight level is selected (with the control on top of the second tab) turns blue;
- the small rectangles connecting the segments are the hysteresis;
- the vertical blue line is the current light sensor value (only available when AutoLight is running);
- the horizontal blue line is the current backlight level (only available when AutoLight is running).
User offset change and increment/decrement backlight command line utility
If you are not satisfied with the backlight level as computed by AutoLight you can add a positive or negative offset to it. The offset values, one for use when on battery and one for use when on AC power, can be entered using the Configurator. Moreover, installation puts the small utility ChangeLight.exe together with AutoLight.exe. Running ChangeLight.exe with parameter "/-" decrements backlight level by one, with parameter "/+" increments backlight level by one. The utility then adjusts current offset level accordingly. Using ChangeLight.exe and a hardware button mapper you can change backlight and offset without using the stylus.
If you do not use ChangeLight.exe you can safely delete it.
Like it? Share with your friends!
If you got an error while installing Themes, Software or Games, please, read FAQ.
Supported operating systems:
Windows Mobile 5.0, Windows Mobile 6 Classic, Windows Mobile 6 Professional, Windows Mobile 6.1 Classic, Windows Mobile 6.1 Professional
Similar Software:
Backstep Backstep - This is a simple utility that will toggle the backlight of a Compaq iPaq from Off-Low-High-Low-Off each time it is run. There is no user interface, it just does its job and exits. I have assigned it to the record button on my iPAQ, so that I can easily toggle the backlight off and on whenever I wish
GfxBoost GfxBoost - activates "QTV" mode for specific surfaces. This makes for example DirectDraw display smoother and: a bit slower or significantly faster, depending on how you look at it. It also seems to have a small effect on Direct3D/OpenGL.
This is a bit tricky! If you will benchmark it the result will be lower FPS. However, it will actually appear faster
Morse Torch Morse Torch - convert your mobile into a pocket torch! This torch comes with a PTT key that allows you to use the torch for sending a message in morse code. The programm uses the mobile's flashlight LEDs.
Try the free demo version! This program is designed to work with HTC HD2, no other models have been tested for compatibility so far
LoveLight LoveLight - This program converts your PocketPC into a flashlight.
This program requires that you have both the 'BeanDLL.dll' file ** and ** the runtime files for Visual Basic on your PocketPC computer. Simply unzip the file for your processor and place the DLL file in the 'Windows' folder of your PocketPC computer. For free support on installing email me
Mobile FlashLight Mobile FlashLight - Many people today carry mini-flashlights on the end of their key chain. Apparently there is a need for this type of device because many stores sell them near the cash registers in the checkout lines. I wonder why these mini-flashlights are so popular when almost everyone has a mobile phone today
Easy FlashLight Easy FlashLight is a simple utility the turns your Windows Mobile device into a flashlight. Easy Flashlight has built in controls to change your backlight settings. With full screen several fun silhouettes you can make being caught in the dark fun
DiscoLight DiscoLight - DiscoLight displays disco-like lights on the screen of your Pocket PC.
DiscoLights requires that you have both the 'BeanDLL.dll' file ** and ** the runtime files for Visual Basic on your PocketPC computer. Simply unzip the file for your processor and place the DLL file in the 'Windows' folder of your PocketPC computer
Zensor2 Zensor2 is an application for automatically rotating your screen using HTC Touch Pro / HTC Touch Diamond's GSensor.
Unlike most other applications, Zensor is written to only detect firm moves, skipping moves done by your mobile moving in your pocket or when walking
Mobile ScreenTester Mobile ScreenTester is excellent for testing your PDA''s display to quickly find dead pixels. It is simple to use and it is also a very thin application and it is FREE!
Comments on Auto Light:
Comments not found
If you noted an error or download link is broken, please, report it via this page or use comments.
Auto Light is compatible with your device Bluebird Pidion BIP-1300