Lamp only displays a never-ending white screen which has no value expect that it can be used as a backup lamp. At the bottom of the screen, the battery percentage level is displayed.
No parameters, no special features - excepts that UP and DOWN buttons can be used to increase/decrease brightness. Tap on the screen to exit the application.
WARNING: if run unattended, this application can drain your mobile battery, as the device auto-off is disabled. Of course, default setting are restored when leaving the application
Like it? Share with your friends!
Supported operating systems:
Palm OS 3.x, Palm OS 4.x, Palm OS 5.x
Similar Software:
Backlight Combo Backlight Combo is designed to be the ultimate solution for effective use of the backlight on the recent Palm models (Palm Vx and the m50x series).
Backlight Combo consists of two separate programs that work together: Backlight Panel (BLT-Panel.prc) and Backlight Hack (BLT-hack.prc)
TinyMirror TinyMirror - Unlike other mirrors, TinyMirror uses the whole screen (there is no annoying menu bar to ruin your reflection).
TinyMirror can also display an all black or an all white screen.
You can toggle between the two by pressing the scroll buttons.
TinyMirror can also conveniently transform into a flashlight if the backlight is turned on
Eye Mail Eye-Mail is intended to capitalize on the bright, hi-contrast display of color Palmsto send scrolling billboard messages
AppLight Hack AppLight Hack - control the Backlight state for a specific application
ZoomThis ZoomThis allows you to magnify portions of your handheld display. Use ZoomThis to magnify phone numbers, addresses, or any other information. ZoomThis is particularly useful when ambient light is low, and the backlight is not enough. Just tap two corners of the area you want to magnify! Works on PalmOS 3.5 or higher
Twinkle Twinkle Little Pix! Twinkle Twinkle Little Pix! can help you to check the Dead Pixel at your Color Screen
ReDigi ReDigi - ReDigi helps you to access the digitizer screen when your pen is severely misaligned.
Calibrate after a soft reset - Normally, after a soft reset, the Prefs screen will appear. With ReDigi, the calibration screen will show after a soft reset. This allows you to calibrate the digitizer
GreenLightHack GreenLightHack is a HackMaster hack that reverses the polarity of the screen when the backlight is turned on (all white pixels become black and all black pixels become white).
This has the effect of making the backlight on the old Palm models (Palm III and below) look like the new ones, and the backlight on the new ones (Palm IIIx and above) look like the old ones
Backlight On Backlight On will turn on the backlight of your m505 every time you turn your Palm on.
Backlight On differs from the "official" Palm app in several ways:
-There is never any user interface. It just works, and doesn't need to be configured.
- It is much smaller (under 1Kb).
- It turns on the backlight everytime the m505 is turned on
Lightswitch for Palm Lightswitch for Palm is a software control for switching the backlight off and on.
This is faster and easier than holding down the power button.
For PDA's not fitted with a backlight, it lets you adjust the brightness.
What's New in This Release:
· Explicit turn backlight on ond off buttons
· Show backlight status, whether off or on
Other Software by developer «Pierre Lescuyer»:
Polyedre by Pierre Polyedre by Pierre does nothing really useful. Pre-defined 3D grid volumes can be rotated around two axis using up / down / left / right hard buttons. This simple program was my first attempt for using Palm SDK graphic lib and hard button management.
Rotating step can be tuned through the Preferences.
This program works fine on Palm OS 3.5 and above
QuarkBox by Pierre QuarkBox by Pierre is a simulation of particles confined in a box, to observe effect of gravity on trajectories. Up to 100 particles can be added/removed using up/down hard buttons. Gravity can be tuned as in preferences.
This program requires Palm OS 3.5 or above. Color as well as Grayscale devices are supported
UmtsCrunch by Pierre UmtsCrunch by Pierre is a database for UMTS Release 5 specifications, the so-called 3rd generation telecommunication system. The Zip file contains a .PRC and a .PDB file which need to be both installed on the Palm.
The program allows any kind of search through the list of database entries.
The database only contains specification title and name
Metronome by Pierre Metronome by Pierre is a full featured electronic metronome.
Pulse volume, frequency and duration can be adjusted on a single screen.
In addition, Auto-off can be disabled (for usage over long period of time) and battery status can be displayed.
This program works fine on Palm OS 3.5 and above. Tested on the palm M and T series
