Auto Light lets you customize the different levels of brightness according the the environment. You just need to choose the brightness level (from 1 to 10) and set the limits of the sensor to the change the level. It is supposed to be better auto adjuster of the backlight for your phone.
Install
Run AutoLight.cab and install in main memory (not in storage card), run AutoLight.Config.cab and install where you like, then softreset (this should also disable the native auto adjust backlight function, check for that in the Control Panel Power applet).
If you have previously installed autolight V2.x and want only upgrade to V2.3 without having your configuration reset to default use the Configurator to stop AutoLight. After that overwrite AutoLight.exe, ChangeLight.exe and AutoLightConfig.exe with the files you find inside AutoLight.zip and softreset.
Configurator
AutoLight working depends on parameters it gets from registry. For details on parameters see AutoLight.reg.txt and AutoLigth.reg
The Configurator gives a more user friendly access to these parameters.
Nevertheless, the configuration process is quite complex and should be done after thoroughly reading AutoLight.reg.txt.
The second tab of the Configurator contains a graphical representation of the calibration table used to convert light sensor to backlight values. Note that: - the horizontal scale is not linear but goes according to square root of the light sensor value;
- the horizontal red segments represent the ranges of light sensor values assigned to every backlight level;
- the horizontal red segment whose backlight level is selected (with the control on top of the second tab) turns blue;
- the small rectangles connecting the segments are the hysteresis;
- the vertical blue line is the current light sensor value (only available when AutoLight is running);
- the horizontal blue line is the current backlight level (only available when AutoLight is running).
User offset change and increment/decrement backlight command line utility
If you are not satisfied with the backlight level as computed by AutoLight you can add a positive or negative offset to it. The offset values, one for use when on battery and one for use when on AC power, can be entered using the Configurator. Moreover, installation puts the small utility ChangeLight.exe together with AutoLight.exe. Running ChangeLight.exe with parameter "/-" decrements backlight level by one, with parameter "/+" increments backlight level by one. The utility then adjusts current offset level accordingly. Using ChangeLight.exe and a hardware button mapper you can change backlight and offset without using the stylus.
If you do not use ChangeLight.exe you can safely delete it.
Like it? Share with your friends!
If you got an error while installing Themes, Software or Games, please, read FAQ.
Supported operating systems:
Windows Mobile 5.0, Windows Mobile 6 Classic, Windows Mobile 6 Professional, Windows Mobile 6.1 Classic, Windows Mobile 6.1 Professional
Similar Software:
SmartLight Automatic Backlight Tired of the display backlight going out when you are looking at the screen - e.g. while thinking about the right word for an sms? Wouldn't it be nice if your phone knew when you needed the light and when not? SmartLight does just that: Once you have opened an application, the backlight stays on - until you close or hide the application, switching the light off automatically
G-Light G-Light - Adjust your backlight levels according to the values your light sensor measures.
Because I wasn't satisfied with the automatic backlight adjustment of my Diamond (it was always too bright for my needs), I made G-Light.
With this tool you can adjust your backlight levels according to the values your light sensor measures..
BacklightTimer BacklightTimer powers off your PocketPC display for a set time interval. Select the hours/minutes and tap the button to power off your PocketPC display. Once the timer has finished the program will turn on the display. NOTE: You can also press the 'On' button on your device to power on the display
Kai's Screen Rotator.Net Kai's Screen Rotator.Net - With this free program you can turn the screen in all 4 directions. You can lay the program on a button for fast access. This program is of special interest for devices where a rotate function is not more available, e.g. HTC Touch Diamond
TouchLockPro TouchLockPro is designed not to interfere with running applications and is a multipurpose locking application. Other locking solutions are often specific for locking only incoming calls/SMS. A lot of locking solutions also place a (transparent looking) Window on top of the running application (e.g
CEBeans FlashLight CEBeans FlashLight - This program converts your Pocket PC into a flashlight.
This program requires that you have both the 'BeanDLL.dll' file ** and ** the runtime files for Visual Basic on your PocketPC computer. Simply unzip the file for your processor and place the DLL file in the 'Windows' folder of your PocketPC computer
TouchResponse TouchResponse - This program is a touch driver to handle the touchscreen presses and vibration. TouchResponse will vibrate on touch.
A settings program exists to configure how the vibration works. Since this is a touch driver, there is no program you need to run to start it
Extended Control Extended Control - Pocket PC Control Panel settings are notoriously difficult to access. Extended Control puts configurable icons on your today screen which provide direct access to frequently used settings.
In addition, there's a running display of used program memory, storage memory and battery strength percentages
Comments on Auto Light:
Comments not found
If you noted an error or download link is broken, please, report it via this page or use comments.
Auto Light is compatible with your device Dopod E806c (HTC Wave)
