EVDash is a Palm OS application that acts as a set of dash board gauges for electric vehicles. It displays battery pack voltage, amps being drawn from the battery pack, and two different estimates of remaining battery capacity. It works with Xantrex's Link 10, formerly called the E-Meter. Just plug the Palm device into the E-Meter, preferably through an optical isolator to protect the Palm device and start the EVDash program.
- Voltage - Battery pack voltage.
- Amps - Amps being drawn from or put back into the battery pack.
- Capacity based on voltage - Capacity calculated from the pack voltage under very low load. Voltage drops off as pack capacity drops.
- Capacity based on amps - Capacity calculated from the amps drawn integrated over time compared to the pack capacity. The peukert effect is taken into account.
Once you install the EVDash.prc on the Palm pull down the menu and go to the setup window. Enter the pack capacity and the Peukerts constant. The state of charge voltages should be determined experimentally by recording the voltages as the battery pack is completely discharged.
To transfer ASCII data from your Palm, use the standard Hot sync cable and a terminal program. Set the following communications information:
Supported operating systems:
Palm OS 3.x, Palm OS 4.x, Palm OS 5.x
Similar Software:
MenuHack MenuHack - corrects a small user interface deficiency in the Pilot. Ordinarily, clicking in the title bar of an application does nothing, which is very counter-intuitive for anyone used to the drop-down menus of Macs and PCs
PalmBuzzer PalmBuzzer allows you to set sound to the 4 hardware buttons, to letters and numbers and to add a picture on top of the window.
These are the naming rules at the moment:
Every file needs to be a WAVE audio file and stored in /PALM/Programs/PalmBuzzer/
* for the 16 on-screen buttons: Test1.wav to Test16.wav
* for the 4 hardware buttons: Hard1.wav to Hard4
Z-Digitizer Z-Digitizer - If you have a digitizer problem this program may help.
As I think you digitizer is not good enough to reach the application icon.
All you have to do are:
- Install this ZDigitize.prc in your Palm.
- Do the soft reset only.
- After the soft reset your Palm will let you celibate the Digitizer
UpDnHack UpDnHack - This is a simple hack which toggles between PgUp and PgDown hardware buttons.
I read a lot from my Palm Vx device and I found that plam's PgDown button is not convenient enough
FontHack 123 Replace the system fonts wholesale or per application. Use your own fonts if you have Pilot Font Editor v3.0
MSMount MSMount - MSMount allow you to access palm applications and databases that are on the Memory Stick or SD card as if they are on the DRAM of Palm device.
With this MSMount, an application that is not support Virtual File System can access to Memory Stick or SD card.
You can move large databases (ex
ColourPop ColourPop is a hack to open a pop-up window in any application with a 256 colour chart
ShutOff! ShutOff! shuts off your device after a period of some seconds.
· Countdown between 2 and 30 seconds
· Can simulate autopoweroff (Softoff) or hardbutton-use (Hardoff)
· Beeptones every second or once before shutoff or quiet
· Pause-button
· High security when used with PadlockHacks smartoption
Clie Jog MP3 Playback Hack Clie Jog MP3 Playback Hack - RNS:: Clie Jog MP3 Playback Hack (CJMP Hack) overrides default Jog Dial navigator's functionality with its own:
- Push the Jog to toggle the playback.
- Push-and-hold the Jog for the next track.
- Rotate the Jog to adjust the volume level.
..
C4 C4 is a small freeware which allows you to change your Palm password without knowing the old password
Other Software by developer «Peter Ohler»:
EV1Dash EV1Dash is a program for Palm OS devices that will collect data from the EV1 and display it on the Palm OS device display. The intent is to provide more information to the driver so that range and performance can be optimized. Here is one of the displays. There are two other displays
