Auto Light lets you customize the different levels of brightness according the the environment. You just need to choose the brightness level (from 1 to 10) and set the limits of the sensor to the change the level. It is supposed to be better auto adjuster of the backlight for your phone.
Install
Run AutoLight.cab and install in main memory (not in storage card), run AutoLight.Config.cab and install where you like, then softreset (this should also disable the native auto adjust backlight function, check for that in the Control Panel Power applet).
If you have previously installed autolight V2.x and want only upgrade to V2.3 without having your configuration reset to default use the Configurator to stop AutoLight. After that overwrite AutoLight.exe, ChangeLight.exe and AutoLightConfig.exe with the files you find inside AutoLight.zip and softreset.
Configurator
AutoLight working depends on parameters it gets from registry. For details on parameters see AutoLight.reg.txt and AutoLigth.reg
The Configurator gives a more user friendly access to these parameters.
Nevertheless, the configuration process is quite complex and should be done after thoroughly reading AutoLight.reg.txt.
The second tab of the Configurator contains a graphical representation of the calibration table used to convert light sensor to backlight values. Note that: - the horizontal scale is not linear but goes according to square root of the light sensor value;
- the horizontal red segments represent the ranges of light sensor values assigned to every backlight level;
- the horizontal red segment whose backlight level is selected (with the control on top of the second tab) turns blue;
- the small rectangles connecting the segments are the hysteresis;
- the vertical blue line is the current light sensor value (only available when AutoLight is running);
- the horizontal blue line is the current backlight level (only available when AutoLight is running).
User offset change and increment/decrement backlight command line utility
If you are not satisfied with the backlight level as computed by AutoLight you can add a positive or negative offset to it. The offset values, one for use when on battery and one for use when on AC power, can be entered using the Configurator. Moreover, installation puts the small utility ChangeLight.exe together with AutoLight.exe. Running ChangeLight.exe with parameter "/-" decrements backlight level by one, with parameter "/+" increments backlight level by one. The utility then adjusts current offset level accordingly. Using ChangeLight.exe and a hardware button mapper you can change backlight and offset without using the stylus.
If you do not use ChangeLight.exe you can safely delete it.
Like it? Share with your friends!
If you got an error while installing Themes, Software or Games, please, read FAQ.
Supported operating systems:
Windows Mobile 5.0, Windows Mobile 6 Classic, Windows Mobile 6 Professional, Windows Mobile 6.1 Classic, Windows Mobile 6.1 Professional
Similar Software:
Gyrator Gyrator has an advanced graphical configuration interface which can be used to create thousands of combinations of events to suit every users needs. Windows can be excluded from all events, or only some of them. Customizable sound events can be triggered, and the device can be made to vibrate for any event
Prog Reso Swap Prog Reso Swap-this program enables you to easily switch individual applications on your Pocket PC Windows 2003 SE between low-resolution QVGA and high-resolution VGA. This is only useful for Windows Mobile 2003 "SE" (Second Edition), and users of VGA Pocket PCs like Toshiba e800
VJCandela VJCandela - Turn you phone into a super bright torch!
This program is used to permit control of the flash light on the Universal family of HTC Phones, to allow it to be used as a torch etc.
Note: this may cause damage to your hardware over prolonged periods! I don't see why it should, but use at your own risk
disCali disCali - disCali disables the "Align Screen" that pops up whenever you press the middle D-PAD button + Message Button.
Instructions:
1. Install the cab.
2. Run "disCali" form Start Menu > Programs, this will disable the align screen function from your entire device until soft-rest (even from the control panel).
3
Keylight Activate / Deactivate the keyboard LEDs on Treo 700w/750v, HTC TyTn, MDA Pro, MDA III and others
Force High Resolution Force High Resolution - Many applications display poorly on Pocket PC VGA as they don't support VGA mode, but use "double pixelisation". There's a work-around for this problem without having to go to "Full VGA" (as SE_VGA and OzVGA do). But this requires adding a little file next to each specific executable
DevState DevState - This is today plug-in for Pocket PC 2003 and Windows Mobile 5.0. This enables to add mainly 3 functions on your today screen like below:
- Displays Memory/Storage status.
- Displays Battery/Power status and it has following function.
>> Soft reset.
>> Turn off your device
SafetyLight SafetyLight - This program is a flashing safety light that you use when you are trick or treating.
This program requires that you have both the 'BeanDLL.dll' file ** and ** the runtime files for Visual Basic on your PocketPC computer. Simply unzip the file for your processor and place the DLL file in the 'Windows' folder of your PocketPC computer
EmergencyFlasher EmergencyFlasher - EmergencyFlasher can display a flashing light and it can be used when in emergency situations, at night.
EmergencyFlasher requires that you have both the 'BeanDLL.dll' file ** and ** the runtime files for Visual Basic on your PocketPC computer
